Shipping options
Calculated individually for your region
Warranty
5 years from sale date
Opportunity to get samples and promotional materials
Manufacturer official website
You are on the official website of terneo and ZUBR brands manufacturer! Order directly from the manufacturer!
The multifunctional relay ZUBR MF is designed to protect the single phase electric grid from unacceptable voltage deviations, as well as exceeding current consumption and actual power. With it, you can limit the actual power consumption of connected equipment. The relay operates on the cutoff principle: if the set values are exceeded, it turns off the load.
Manuals in other languages: Lithuanian
The relay will resume the load supply after the set time when the emergency is over and the voltage in the network has stabilized. You can adjust the load delay time from 3 to 600 seconds. For equipment sensitive to frequent power on/off (refrigerators, air conditioners, etc.), we recommend setting the delay value at 120-180 seconds.
You can adjust the load turn off delay when the current consumption and the actual power are exceeded safely . The delay time range is from 0 to 240 seconds.
Voltage supply will start after the delay time (green indicator will be activated).
Voltage and current measurement accuracy
The relay provides a high level of accuracy in measuring voltage, current, and actual power using the True RMS algorithm. However, you can adjust the display of these parameters according to your control device.
The housing of the device is made of non-flammable polycarbonate. The relay is also equipped with a thermal sensor that protects from overheating.
The multifunctional relay is controlled by only three buttons. The upper and lower buttons are used to set the upper and lower voltage limits accordingly. The middle button opens a menu where you can adjust the maximum current and power consumption. The menu sets the delay time of voltage switch on, as well as the time of disconnection of load supply when the permissible values of current and power are exceeded.
The relay stores critical values of voltage, current and actual power in non-volatile memory.
The multifunctional relay is installed in the switchboard on the standard DIN rail. The width of the device is only 53 mm.
Question:
Здравствуйте. Приобрел ZUBR MF25 и крайне недоволен сим фактом. Показывает мой прибор потребляемую мощность в 4 раза выше действительной, и соответственно отключает питание. Например, духовой шкаф мощностью 3кВт при работе показывается как 12 кВт, стиральная машина 2 кВт - 8 кВт и тд.. Подскажите , можно ли как то отрегулировать это значение и почему так вообще происходит?Question:
Добрый день.Проясните ситуацию pls. В документации на ZUBR MF 25 и на ZUBR RET I25 приведена схема подключения, из которой следует, что реле отключает по превышению нагрузку, мощность которой измеряет, т.е. нагрузку подключенную на клеммы 1 и 3.
В то же время в документации написано "Напряжение питания (100–420 В, 50 Гц), в котором будет контролироваться ток и мощность, подается на клеммы 1 и 2".
Так где измеряется мощность по превышению которой произойдет отключение нагрузки? На клеммах 1 и 2 или как на схеме, 1 и 3?
Мне это важно. Я не могу понять из описания + схема, можно ли эти устройства использовать как реле приоритета нагрузки. Мне надо от одной розетки запитать и стиральную машину (2.8 кВт) и бойлер (2.2 кВт) так, что бы когда стиральная машина греет воду, бойлер не включался.
Добрый день. Эти реле не работают по приоритету нагрузки. Для питания реле необходимо подать напряжение на клеммы 1 (ноль с нулевого клемника) и 2 (фаза). Нагрузка подключается к клемме 3 (фаза) и к нулевому клемнику. Реле измеряет ток по фазному проводу. Отключается нагрузка, если ее значение (мощности или тока) превышает установленное в настройках реле.
Question:
Я хачу си купит многофункционалное реле ZUBR DF 25. Имам адрес в чехию..Е то возможно? И как?Добрый день, свяжитесь, пожалуйста, с нашим менеджером, [email protected], либо оставьте свои контактные данные.
Question:
Скілки років гарантія на даний прилад ZUBR MF63 ?Дякую!
5 років з дня продажу
Question:
Добрий день подключил реле верхня шкала показует две нижних по нолях нагрузки не давал. Откуда ноль брать із шини или із водного автомата.Добрий день. Середній та нижній індикатори показують струм та потужність підключеного навантаження. Якщо навантаження не підключено, ці індикатори будуть відображати нуль. Нуль можна взяти з нульової шини. Якщо її немає, тоді з водного автомата, який стоїть по нулю.
Question:
подскажите если реле многофункциональное обязательно ставить автоматы или нетДобрый день, обязательно.
Question:
Доброе утро.Каждую ночь, прыгает напряжение, так как новострой и питание идет временное. У меня верхний предел стоит на 245, скажите пожалуйста, до скольки можно его поднять, безопасно для техники и котла отопления, спасибо. Максим Киев
Доброе утро, при настройке пределов напряжения необходимо руководствоваться данными из технической документации к защищаемому оборудованию. Мы не рекомендуем устанавливать верхний предел напряжения выше 250 В.